鸿森主营产品:纯实木门厂家 | 实木进户门 | 原木进户门 | 铜木门厂家 | 铝木车库门 | 原木装甲门 | 电动庭院门 | 浙江双雄门业

行业资讯

当前位置:网站首页 > 新闻动态 > 行业资讯

  • 实木门安装操作工艺流程是什么?
  • 本站编辑:杭州鸿森门业有限公司发布日期:2019-04-01 07:20 浏览次数:
实木门安装操作工艺流程!鸿森门业有限公司根据目前国内家居市场装修个性化的特点,一方面加强和全球工业产品设计学院的研发合作;另一方面积极培养自己的室内门技术人才,我们一直致力于实木门的新工艺、新产品的研发,不断提升木门品牌产品品质……1. 门套及门扇在使用前必须仔细检查是否合格,是否有颗粒和油漆,是否有流泪状,有无碰伤,挂痕门套和门扇宽度是否是下单要求的尺寸。
 
         2. 在安装门套前先将门套板组装在一起,将组装好的门套安装于以调校规范的门洞中并用直钉将门套简单固定在基层上。 
 
         3. 根据门扇在开启方向在门扇上开合页口和锁孔上合页,并把门扇简单用螺钉固定在门套上,以门扇为基准,将四周缝隙按要求(门扇左右上口间隙2-3mm,门扇与地面面层高度距离7-10mm调匀)同时调校其垂直度和搓角度要求横平竖直,误差+-1mm再用直钉固定和用木螺钉在挡门条草槽中把门套固定在基层上。 
 
         4. 安装挡门条,根据门套安装后尺寸,把挡门条栽好在挡门条背面涂白乳胶,先安装顶板挡门条再安装侧板挡门条,再次调校门扇缝隙并用螺钉固定门扇。 
 
         5. 安装门边线先将门套上安装门边线的嵌槽用螺机铣通,再将门边线按所需要求长度下端剧切好和切45度角嵌条,涂白乳胶依次装贴双面门边线碰角处应严密平整,肉眼距50mm应不见接缝。 
 
         6. 门锁安装,门锁离地高度900——1000mm(锁中心位)锁孔位置正确,锁舌与门扇锁扣与门框之间的缝隙严实、安装牢固、开关自如。锁安装后必须包扎保护以防污染。 
 
         7. 玻璃安装,装门扇涉及磨沙玻璃时,装好后应在磨沙玻璃光面部分打适量玻璃胶,保护玻璃橱卫间磨沙面应向外,与室外交结出磨沙面应向内。 
 
         8. 门套安装完成后自检合格进行灰补,修色,点漆再全面检查,这样一套完整的木门就安装完成了


Solid wood door installation operation process! Hongsen Door Industry Co., Ltd. strengthens its R&D cooperation with the Global Institute of Industrial Product Design on the one hand, and cultivates its own indoor door technicians on the other hand. We have been devoting ourselves to the research and development of new technologies and products of solid wood doors, and constantly improve the quality of brand products of wood doors. 1. Before using the door cover and the door fan, we must carefully check whether they are qualified, whether there are particles and paints, whether there are tears, whether there are bruises, whether the width of the hanging mark door cover and the door fan is the required size for placing the order.
 
 
 
2. Before installing the door cover, assemble the door cover plate together, install the assembled door cover in the door hole to adjust the specifications, and fix the door cover on the base simply with straight nails.
 
 
 
3. According to the opening direction of the door fan, the door door door opens the hinge and the lock hole, and fixes the door simply with screw on the door cover. Taking the door fan as the benchmark, the gap around the door is adjusted according to the requirements (the gap between the left and right upper ports of the door fan is 2-3 mm, the height distance between the door fan and the ground layer is 7-10 mm). At the same time, the verticality and rubbing angle of the door fan are adjusted to be horizontal and vertical, and the error is +1 mm, then fixed with vertical screw and wood screw. The door cover is fixed on the base by nailing in the straw groove of the guard strip.
 
 
 
4. Install the blocking bar. According to the size of the door cover after installation, plant the blocking bar on the back of the blocking bar and coat it with white latex. Firstly, install the roof blocking bar and then install the side blocking bar. Secondly, adjust the gap of the door fan and fix the door fan with screw.
 
 
 
5. Install the edge line of the door by milling the slot of the edge line of the door sleeve with a screw machine. Then cut the edge line of the door sharply and cut the 45 degree angle strip according to the required length. The corner of the edge line of the double-sided door should be tightly and smoothly coated with white latex in turn, and the seam should not be seen with 50 mm naked eye distance.
 
 
 
6. Lock installation. Lock height 900-1000mm (lock center position) is correct. The gap between lock tongue and door lock and door frame is tight, the installation is firm and the switch is free. After the lock is installed, it must be bandaged and protected to prevent pollution.
 
 
 
7. When installing glass, when installing doors and fans involving grinding glass, proper amount of glass glue should be applied on the polished surface of grinding glass to protect the grinding surface of glass cabinet bathroom and outdoor grinding surface should be inward.
 
 
 
8. After the installation of the door cover, the self-inspection qualified for gray repairing, color repairing, painting and comprehensive inspection, so that a complete set of wooden doors are installed.